200 ps8196 05/05/98 1234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901 2123456789012 1234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901 2123456789012 PI5C34X2245 32-bit, 2-port busswitch with 25 w w w w w series resistor 1234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901 2123456789012 1234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901 2123456789012 product features: ? near-zero propagation delay ?25 w series resistor termination ?5 w switches connect inputs to outputs ? direct bus connection when switches are on ? ultra-low quiescent power (0.2 a typical) C ideally suited for notebook applications ? pin compatible with qs34x245 ? industrial operating temperature: C40c to +85c ? packages available: C 80-pin 150 mil wide plastic bqsop (b) PI5C34X2245 logic block diagram product pin configuration product pin description pin name i/o description ben i bus enable input (active low) a 0 -a 31 i/o bus a b 0 -b 31 i/o bus b function ben a 0C31 disconnect h hi-z connect l b 0C31 truth table (1) note: 1. h = high voltage level l = low voltage level hi-z = high impedance product description: pericom semiconductors pi5c series of logic circuits are produced in the companys advanced 0.6 micron cmos technology. the PI5C34X2245 is a 32-bit, 2-port bus switch. four enable signals (ben) turn the switches on. the bus switch creates no additional propagational delay or additional ground bounce noise. the device has a built-in 25 w resistor to reduce noise resulting from reflection, thus eliminating the need for an external terminating resistor. 32-bit, 2-port busswitch with 25 w w w w w series resistor be 1 a 7 a 0 b 7 b 0 be 2 a 15 a 8 b 15 b 8 be 3 a 23 a 16 b 23 b 16 be 4 a 31 a 24 b 31 b 24 nc 1 2 3 4 5 6 7 8 9 gnd 10 11 12 13 14 15 16 17 18 19 20 gnd be1 80 79 78 77 76 75 v cc 74 73 72 71 70 69 68 67 66 65 64 63 62 b 15 61 a 0 a 1 a 2 a 3 a 4 a 5 a 6 a 7 nc a 8 a 9 a 10 a 11 a 12 a 13 a 14 a 15 b 14 b 13 b 12 b 11 b 10 b 9 b 8 be2 v cc b 0 b 1 b 2 b 3 b 4 b 5 b 6 b 7 nc 21 22 23 24 25 26 27 28 29 gnd 30 31 32 33 34 35 36 37 38 39 40 gnd be3 60 59 58 57 56 55 v cc 54 53 52 51 50 49 48 47 46 45 44 43 42 b 31 41 a 16 a 17 a 18 a 19 a 20 a 21 a 22 a 23 nc a 24 a 25 a 26 a 27 a 28 a 29 a 30 a 31 b 30 b 29 b 28 b 27 b 26 b 25 b 24 be4 v cc b 16 b 17 b 18 b 19 b 20 b 21 b 22 b 23 80-pin b80
201 PI5C34X2245 32-bit, 2-port busswitch with 25 w w w w w series resistor ps8196 05/05/98 1234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901 2123456789012 1234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901 2123456789012 1234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901 2123456789012 1234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901 2123456789012 maximum ratings (above which the useful life may be impaired. for user guidelines, not tested.) storage temperature ............................................................ C65c to +150c ambient temperature with power applied ........................... C40c to +85c supply voltage to ground potential (inputs & vcc only) .... C0.5v to +7.0v supply voltage to ground potential (outputs & d/o only) C0.5v to +7.0v dc input voltage .................................................................. C0.5v to +7.0v dc output current ............................................................................ 120 ma power dissipation ................................................................................... 0.5w note: stresses greater than those listed under maximum ratings may cause permanent damage to the device. this is a stress rating only and functional operation of the device at these or any other con- ditions above those indicated in the operational sections of this specification is not implied. exposure to absolute maximum rating conditions for extended periods may affect reliability. dc electrical characteristics (over the operating range, t a = C40c to +85c, v cc = 5v 10%) parameters description test conditions (1) min. typ (2) max. units v ih input high voltage guaranteed logic high level 2.0 v v il input low voltage guaranteed logic low level C0.5 0.8 v i ih input high current v cc = max., v in = v cc 1a i il input low current v cc = max., v in = gnd 1 a i ozh high impedance output current 0 - a, b - v cc 1a v ik clamp diode voltage v cc = min., i in = C18 ma C0.7 C1.2 v i os short circuit current (3) a (b) = 0v, b (a) = v cc 100 ma v h input hysteresis at control pins 150 mv r on switch on resistance (4) v cc = min., v in = 0.0v, i on = 48 ma 28 40 w v cc = min., v in = 2.4v, i on = 15 ma 35 48 w capacitance (t a = 25c, f = 1 mhz) parameters (5) description test conditions typ units c in input capacitance v in = 0v 6 pf c off a/b capacitance, switch off v in = 0v 6 pf c on a/b capacitance, switch on v in = 0v 12 pf notes: 1. for max. or min. conditions, use appropriate value specified under electrical characteristics for the applicable device type. 2. typical values are at vcc = 5.0v, t a = 25c ambient and maximum loading. 3. not more than one output should be shorted at one time. duration of t he test should not exceed one second. 4. measured by the voltage drop between a and b pin at indicated current through the switch. on resistance is determined by the lower of the voltages on the two (a,b) pins. 5. this parameter is determined by device characterization but is not production tested.
202 ps8196 05/05/98 1234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901 2123456789012 1234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901 2123456789012 PI5C34X2245 32-bit, 2-port busswitch with 25 w w w w w series resistor power supply characteristics parameters description test conditions (1) min. typ (2) max. units i cc quiescent power v cc = max. v in = gnd or v cc 0.1 3.0 a supply current d i cc supply current per v cc = max. v in = 3.4v (3) 2.5 ma input @ ttl high i ccd supply current per v cc = max., 0.25 ma/ input per mhz (4) a and b pins open mhz ben = gnd control input toggling 50% duty cycle notes: 1. for max. or min. conditions, use appropriate value specified under electrical characteristics for the applicable device. 2. typical values are at vcc = 5.0v, +25c ambient. 3. per ttl driven input (v in = 3.4v, control inputs only); a and b pins do not contribute to icc. 4. this current applies to the control inputs only and represent the current required to switch internal capacitance at the spec ified frequency. the a and b inputs generate no significant ac or dc currents as they transition. this parameter is not tested, but i s guaranteed by design. PI5C34X2245 switching characteristics over operating range PI5C34X2245 com. parameters description conditions (1) min. max. unit t plh propagation delay (2,3) c l = 50 pf 1.25 t phl ax to bx, bx to ax r l = 500 w t pzh bus enable time 1.5 7.5 ns t pzl be x to ax or bx t phz bus disable time 1.5 5.5 t plz bex to ax or bx notes: 1. see test circuit and wave forms. 2. this parameter is guaranteed but not tested on propagation delays. 3. the bus switch contributes no propagational delay other than the rc delay of the on resistance of the switch and the load capacitance. the time constant for the switch alone is of the order of 0.25 ns for 50 pf load. since this time constant is much smaller than the rise/fall times of typical driving signals, it adds very little propagational delay to the system. propagatio nal delay of the bus switch when used in a system is determined by the driving circuit on the driving side of the switch and its interact ion with the load on the driven side. pericom semiconductor corporation 2380 bering drive ? san jose, ca 95131 ? 1-800-435-2336 ? fax (408) 435-1100 ? http://www.pericom.com
|
